Ghost 2 Immobiliser Reviews
The Ghost 2 immobiliser utilizes the latest technology to ward off car theft. This hidden device is not detected by thieves and only starts your engine when a PIN number or app is entered.
It connects to the CAN data network in your vehicle and is weatherproof. It has a service/valet function that lets you temporarily start your vehicle while it is in garage.
Easy to install
The Ghost immobiliser is a cutting-edge security tool that shields your vehicle from cloning, hacking and key theft. It uses a unique PIN code system that is incorporated into the ECU of your vehicle which makes it extremely difficult for thieves to identify or alter. Unlike traditional immobilisers, it doesn't require special keys or sensors, and is completely hidden from view with no LEDs or signals to signal its presence. It is also less expensive than replacing an ECU or installing a new key fob and could lower your monthly insurance premiums.
When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's directions carefully. This will ensure that the device operates efficiently and correctly. After the installation is complete Test the system by entering the PIN code, then turning on the engine. Regular testing will allow you to detect any issues early.
Before you begin the installation, double-check the exact location of the CAN H and CAN L wires. They are vital to powering the immobiliser, and it is important that they are properly connected. It is also a good idea to label the wires to make it easier to locate them during the installation process. Once you have identified the locations of these wires, connect them to a permanent 12V power source as well as an earthing point. Be sure to use a fuse tap if necessary to protect the connections from short circuits or damage.
After connecting the wires, tidy the wires using cable ties to avoid potential interference. It is also recommended to cover the connections with insulation tape or heat shrink tubing. This will protect them from electrical shorts and increase the lifespan of the device. Once the wiring is secure, it's a good idea test the Ghost 2 immobiliser.
In the event that you have to hand over your vehicle, such as for valet parking or servicing or valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. To activate this feature, simply press the brake pedal while holding the accelerator, and press a number of times equal to the first number of the emergency code. The system will enter service mode. This can be confirmed by flashing 5 times the indicator signal.
Easy to change PIN codes
It is simple to safeguard your vehicle from theft with an immobiliser ghost 2. It is hidden inside the vehicle and is accessible only through a specific code. The device communicates directly with the vehicle ECU via its data bus. It does not rely on radio frequency signals, as do traditional Thatcham immobilisers or aftermarket alarm systems. This makes it difficult for thieves to listen for the sound of an immobiliser relay or add new key fobs. The control unit is concealed in the wiring harness or dashboard and cannot be physically tampered with to reset the system.
The ghost 2 immobiliser is connected to your vehicle's CAN Data network and utilizes existing buttons on the steering wheel, door panels, and centre console to create an individual sequence of up to 20 button presses which must be entered before the engine can start - just like a PIN code. This innovative next-generation system does not require any wire cutting upon installation and is fully reprogrammable at anytime. autowatch ghost immobiliser can also put your vehicle in Service or Valet mode to allow it to be started for a short time when you give it to a mechanic for work.
You can also use the app to change your PIN number or disable it completely if you've lost your keys. This feature is especially useful in the event that you have offered your car to someone else for valet parking or servicing, as it stops them from starting your car and taking away without your consent. It is also undetectable to professional thieves as it does not use any radio frequencies or circuit cuts.
Another great feature of the ghost 2 immobiliser is its capability to stop relay thefts. Relay theft is a common method of car theft where criminals attack your car's diagnostic port, then modify the signal that is sent by the key to the vehicle's ECU in order to trick it into believing that the key is valid. The immobiliser of the traditional model can be manipulated in this way, but with the ghost 2 immobiliser the signal is blocked by the immobiliser prior to it reaches the ECU.
Easy to use app
Ghost 2 is a revolutionary immobiliser that protects your car from key-cloning, hacking, and key theft. It connects to the CAN data network of your vehicle and requires a PIN code in order to start the engine. It also deters thieves from using signal spoofing or device spoofing, which are common techniques used to steal vehicles.
The system is simple to use and operates as a normal car alarm. Installing the system will allow you to create a unique 20-digit pin code that you must enter prior to starting the vehicle. This will stop your vehicle from being taken away, even when you lose your keys. You can disable the system using an app for your smartphone.
Unlike other systems that are silent, the ghost is quiet and does not emit any radio frequency signals. It is a weatherproof, discreet device that can be placed in any vehicle. It can be hidden beneath the dash, steering wheel, or even the door panels. It communicates with your ECU over the CAN data circuit, and is not affected by diagnostic tools that some thieves use to identify security systems. It is not affected by jamming devices that spoof codes.
It is a security system that can be used to deter the theft of all vehicles. The technology has been proven efficient, and it's in compliance with TASSA Standards. Ghost is a great solution for classic, sports and prestige cars. It can also be used to secure vehicles that are being let out on websites like Turo.
The Autowatch Ghost 2 represents the next generation of vehicle immobilisers. This system is undetectable to thieves and stops the vehicle from starting without a PIN or are authorised by the app. It also doesn't emit radio frequencies or other signals that can be detected by scanners. The installation process is simple and quick. The app is user-friendly with a simple interface and a simple navigation. It also has an GPS tracker that can assist police locate the vehicle and recover it.
Simple to reset
Ghost 2 immobilisers are an excellent method to guard your vehicle from theft. It connects to your vehicle's ECU to create a barrier that thieves are unable to penetrate without the correct PIN. The device is also TASSA-verified that means it's recognized by insurance companies. It's a great tool to prevent car theft and will save you money in the long run.
Unlike traditional alarm/immobilisers that require circuit cutting and circuit cutting, the Ghost system is directly connected to the vehicle's CAN data network and works with the existing buttons on the dashboard and the steering wheel. You can create an individual PIN sequence, which can be up to 20 presses long. This PIN needs to be entered before the engine can begin, just like a credit card. Ghost is unnoticeable to thieves, and there are no indicators that signal its presence, which makes it the most effective aftermarket CAN bus immobiliser that is on the market today.
Another benefit of the Ghost system is that it doesn't make use of radio frequency signals, which means it is not scanned or intercepted by thieves. This prevents relay attacks and keys that are cloned as well as the more popular method of hacking a vehicle's CAN bus system by scanning for signals from its alarm/immobiliser. The Ghost system is designed so that it is able to be hidden inside your vehicle. There aren't any lights, or other indicators to show its presence.
The system comes with the option of a Transport Mode which disables the Ghost System. This is beneficial for situations when you require temporarily deactivating Ghost, such as when transporting or maintaining your vehicle. However, this mode is not as efficient as Service Mode, as it does not turn off the Ghost system when your vehicle speeds over 31 mph for 15 minutes.
To reset your ghost 2 immobiliser, you will need to have the emergency code, which you can obtain from your installer. It is usually hidden under a scratch-off section on the card that was supplied when you installed the device. This emergency code should be secured and kept in a safe place, such as an at-home wallet.